OE-C3212D4-S Quick Start Guide

Last updated
Save as PDF

Click the link if you need to download the original hardcopy of the OE-C3212D4-S Quick Start Guide included with the boxed contents.

Box Contents

OpenEye C3212D4-S cameras come with self-tapping screws and plastic anchors, mounting template, torx tool, and a waterproof cable connector. Identify the following components to make sure everything has been properly included with your new recorder. If any of the following items are missing, contact the dealer to arrange a replacement.

C3212D8-S Line Drawing.png

OE-C3212D4-S Dome Camera

Screws and Anchors.png

Self-Tapping Screws and Plastic Anchors x3

C33212D8-S mounting template.png

Mounting Template

waterproof cable connector.png

Waterproof Cable Connector

torx tool.png

Torx Tool

Connections

1	RJ45	For network and PoE connections
2	Power (12vDC)	Power Connection (12vDC power input should be plugged when not in use)
3	Audio I/O	Ground
		Audio In
		Audio Out
4	Alarm I/O	Ground
		Alarm In
		Alarm Out -
		Alarm Out +
5	Reset Button	To restore the camera to factory defaults: Disconnect power for 30 seconds. Reconnect power and wait 30 seconds. Press and hold the reset button for 20 seconds.
6	microSD Card Slot	Supports up to 512GB microSD card for Edge storage. Do not add or remove the microSD card when the camera is powered on.
7	Built-in microphone

Power Connection

For an adequate power connection, use a 12vDC adaptor. Alternatively, you can power the camera by PoE if a Power Sourcing Equipment (PSE) switch is available. Ensure that the camera’s power cable is correctly and firmly connected.

NOTE: OpenEye recommends against using more than one power source at a time. Do not use a PoE power source when providing the camera with 12vDC power.

If using Power over Ethernet (PoE), make sure Power Sourcing Equipment (PSE) is in use in the network.

Default Username and Password

*OpenEye IP cameras ship without a default password.

Username: admin

The admin user password can be set using the following methods:

OpenEye recorders running Apex 2.6 or newer will automatically set a new unique password when added in setup, if a new password has not already been set.

NOTE: You can set your Default Camera Password under the General Settings page within Setup > System Settings > General Settings. For instructions on defining your unique camera password, visit Default Camera Password.

Connect to the camera directly through a Web Browser and follow the onscreen prompts.
Use the Network Camera Manager (NCM) Utility.

NOTE: More on the NCM Software can be found at Network Camera Manager.

NOTE: Refer to your recorder manual or quick start guide for instruction on adding cameras.

Assigning an IP Address

OpenEye IP cameras are set to DHCP by default. If a DHCP server is not detected after 2 minutes, the camera will default to IP address 192.168.51.2. If you are not using a DHCP server, NCM will allow you to batch configure a static IP address. The default IP address for the camera network on your recorder is 192.168.51.1.

Selecting multiple cameras and entering IP address 192.168.51.2 will set an IP address on all selected cameras, starting at 192.168.51.2 and increase per camera.

Open the Network Camera Manager application.
Select applicable camera(s).
Input starting Ip address, Subnet Mask, Gateway, DNS.
Apply changes.
Wait 60 seconds before refreshing NCM.

NOTE: See Network Camera Manager for more information.

Product Features

Cameras

Maximum Resolution	2688 x 1520
Frame Rate at Maximum Resolution	30FPS @ 4MP \| H.264/H.265
Total Streams	2
ONVIF	Profile S / G / T Compliant
Day / Night	True Day / Night w/ IR-Cut Filter
Wide Dynamic Range	True WDR @ 4MP; 120dB

Environmental and Power

Power Consumption	7W Max
Input Voltage	12vDC / PoE
Pan / Tilt / Rotate	Pan: 0° ~ 355° Tilt: 0° ~ 80° Rotate: 0° ~ 355°
IP Rating	IP67
Impact Rating	IK10