Skip to main content
OpenEye Knowledge Base

OE-C3011D4-S Quick Start Guide

  1. Last updated
  2. Save as PDF
OE-C3011D4-S Quick Start Guide

Click the link if you need to download the original hardcopy of the OE-C3011D4-S Quick Start Guide included with the boxed contents.

Box Contents

OpenEye C3011D4-S cameras come with self-tapping screws and plastic anchors, mounting template, a tapered RJ45 sleeve, a torx tool, a #2 Phillips bit, 21mm cable grommets, 28mm cable grommets, and a 2-pin terminal block. Identify the following components to make sure everything has been properly included with your new recorder. If any of the following items are missing, contact the dealer to arrange a replacement.

C3011D4-S Line Drawing no Callout.png

OE-C3011D4 -S Turret Camera

Screws and Anchors.png

Self-Tapping Screws and Plastic Anchors x3

C1012D2-S mounting template.png

Mounting Template

 

RJ45 Sleeve.png

Tapered RJ45 Sleeve

 

torx tool.png

Torx Tool

 

Phillips Bit.png

#2 Phillips Bit

Grommets.png

 

2x - 21mm Cable Grommet

Grommets.png

2x - 28mm Cable Grommet

2-Pin Terminal Power Block.png

2-Pin Terminal Block

  
Connections

C3011D4-S Reset and SD.pngC3011D4-S Mic Callout.png

1 RJ45 - For network and PoE connections
2 Power (12vDC) 1 12vDC + Power Connection
2 GND -
3 Reset Button -

To restore the camera to factory defaults:

  1. Disconnect power for 30 seconds.
  2. Reconnect power and wait 30 seconds.
  3. Press and hold the reset button for 20 seconds.
4 Alarm & Audio I/O 1 Alarm Out - Alarm connection
2 Alarm Out +
3 GND Ground connection
4 Alarm In Alarm connection
5 GND Ground connection
6 Audio In Two-way audio transmission
7 GND Ground connection
8 Audio Out Two-way audio transmission
5 microSD Card Slot -

Supports up to 512GB microSD card for Edge storage.

Do not add or remove the microSD card when the camera is powered on.
6 Built-in microphone
Power Connection

For an adequate power connection, use a 12vDC adaptor. Alternatively, you can power the camera by PoE if a Power Sourcing Equipment (PSE) switch is available. Ensure that the camera’s power cable is correctly and firmly connected.

NOTE: OpenEye recommends against using more than one power source at a time. Do not use a PoE power source when providing the camera with 12vDC power.

If using Power over Ethernet (PoE), make sure Power Sourcing Equipment (PSE) is in use in the network.

Default Username and Password

*OpenEye IP cameras ship without a default password.

Username: admin

The admin user password can be set using the following methods:

  1. OpenEye recorders running Apex 2.6 or newer will automatically set a new unique password when added in setup, if a new password has not already been set.

NOTE: You can set your Default Camera Password under the General Settings page within Setup > System Settings > General Settings. For instructions on defining your unique camera password, visit Default Camera Password.

  1. Connect to the camera directly through a Web Browser and follow the onscreen prompts.
  2. Use the Network Camera Manager (NCM) Utility.

NOTE: More on the NCM Software can be found at Network Camera Manager.

NOTE: Refer to your recorder manual or quick start guide for instruction on adding cameras.

Assigning an IP Address

OpenEye IP cameras are set to DHCP by default. If a DHCP server is not detected after 2 minutes, the camera will default to IP address 192.168.51.2. If you are not using a DHCP server, NCM will allow you to batch configure a static IP address. The default IP address for the camera network on your recorder is 192.168.51.1.

Selecting multiple cameras and entering IP address 192.168.51.2 will set an IP address on all selected cameras, starting at 192.168.51.2 and increase per camera.

  1. Open the Network Camera Manager application.
  2. Select applicable camera(s).
  3. Input starting Ip address, Subnet Mask, Gateway, DNS.
  4. Apply changes.
  5. Wait 60 seconds before refreshing NCM.

NOTE: See Network Camera Manager for more information.

Connecting to the IP Camera

To access the camera setup menu, you need to open Network Camera Manager (NCM) utility. NCM is pre-installed on all OpenEye Recorders and is also available for download on the OpenEye website for installation on your personal computer or laptop.

  1. Open Network Camera Manager.
  2. Locate your camera on the Network Camera Manager list.
  3. To open the web browser, select the camera and click LOAD.
Cabling Instructions
  1. Push the RJ45 connector into the tapered sleeve.
  2. Cut the end off the center of the cable grommet and feed the network cable through the opening.
  3. Remove the tapered sleeve.
  4. Insert the RJ45 connector into the network port. Pull the cable downward to make sure the cable grommet protrudes to the direction opposite to the RJ45 connector.

C3011D4-S Cabling Instructions.png

Product Features
Cameras
Maximum Resolution 2688 x 1520
Frame Rate at Maximum Resolution 30FPS @ 4MP  | H.264/H.265
Total Streams 2
ONVIF Profile S / G / T Compliant
Day / Night True Day / Night w/ IR-Cut Filter
Wide Dynamic Range True WDR @ 4MP; 120dB
Environmental and Power
Power Consumption 6.5W Max
Input Voltage 12vDC / PoE
Operating Temperature -22°~131°F (-30°~55°C )
IP Rating IP67
Impact Rating IK10
  1. Back to top
  • Was this article helpful?

Recommended articles

  1. Article type
    Reference
  2. Tags
    This page has no tags.