OE-C8312P2 Hardware Manual - Features and Contents
OE-C8312P2 Hardware Manual - Features and Contents
Important Safeguards
View Important Safeguards before installing the camera.
Warranty
View the Product Warranty for the camera.
Camera Dimensions
Connections
| 1 | RJ-45 Port | For network and PoE+ connections | |
| 2 | Power Connector (AC24V) | AC24V power connection | |
| 3 | Alarm I/O & RS-485 Connector | Alarm I/O & RS-485 connection | NOTE: Do NOT connect external power supply to the alarm I/O connector of the camera. |
| 4 | Reset Button | Press the button with a proper tool for at least 20 seconds to restore the system. | |
| 5 | SD Card Slot | Open the dome cover to reveal the SD Card Slot. Insert the SD card into the card slot to store videos and snapshots. Do not remove the SD card when the camera is powered on. | |
Power Connection
For an adequate power connection, use a 12vDC adaptor. Alternatively, you can power the camera by PoE if a Power Sourcing Equipment (PSE) switch is available. Ensure that the camera’s power cable is correctly and firmly connected.
NOTE: OpenEye recommends against using more than one power source at a time. Do not use a PoE power source when providing the camera with 12vDC power.
If using Power over Ethernet (PoE), make sure Power Sourcing Equipment (PSE) is in use in the network.
To power up the camera, connect the AC24V power adaptor to the power connector of the camera and the power outlet. Refer to the diagram and pin definition below for AC24V power connection.
| 1 | AC24V L |
| 2 | GND |
| 3 | AC24V N |
Alarm I/O Connection
| 1 | Audio Out | 8 | RS-458 D- |
| 2 | GND (Audio I/O) | 9 | Alarm In 4 |
| 3 | Alarm Out A1 | 10 | Alarm In 3 |
| 4 | Alarm Out A2 | 11 | Alarm In 2 |
| 5 | Alarm Out B1 | 12 | Alarm In 1 |
| 6 | Alarm Out B2 | 13 | GND (Alarm I/O & RS-485) |
| 7 | RS-458 D+ | 14 | Audio In |
Camera Cabling Considerations
The OE-C8312P2 has an IP66 Outdoor rating to prevent water from entering the camera. However, proper installation is required for this rating. To ensure that the camera is as water resistant as possible, follow these tips:
- Place all cables and the adapter in a dry and well-insulated environment, such as waterproof boxes. The purpose of the waterproof box is to prevent moisture accumulation inside the camera and moisture penetration into the cables.
- While running cables, slightly bend the cables into a U-shaped curve to make a low point (as illustrated below). The purpose is to prevent water from entering the camera along the cables from above.
To ensure a watertight seal, the cable entry hole of the outdoor mounting kit needs to be sealed with thread seal tape to avoid water from entering the camera.
Features
- Remotely PTZ Repositionable
- 360° Coverage
- Easy Single Cable Installation
- True WDR
- True Day / Night
- Integrated Heater
- 4.3~170mm AF, 40x Zoom Lens
- Audio I/O
- Alarm I/O
- Sunshield
- 1.5-Inch Standard Threaded Mount Type
- IK10 Impact Protection Rating
- IP66 Ingress Protection Rating
- Smart Compression
- NDAA Compliant
Box Contents
OpenEye C8312P2 cameras come with security screws, threaded pendant mount, threaded mount adapter, security torx tool, 3-pin power terminal block, and 14-pin alarm I/O terminal block. Identify the following components to make sure everything has been properly included with your new recorder. If any of the following items are missing, contact the dealer to arrange a replacement.
|
OE-C8312P2 PTZ Camera |
M4 x 8mm Security Screw with Rubber |
|
Threaded Pendant Mount |
Threaded Mount Adapter |
|
Security Torx Tool |
3-Pin Power Terminal Block (AC 24V Use) |
|
14-Pin Alarm I/O Terminal Block |
Related Links